CTTA in TEMPEST: Certification Levels and SCIF Accreditation

A Certified TEMPEST Technical Authority, or CTTA, is a U.S. government employee who has met the certification requirements set by the Committee on National Security Systems and been formally appointed to decide what TEMPEST countermeasures a classified facility or system needs, verify that those countermeasures work, and sign off before any classified processing begins.1National Institute of Standards and Technology. Certified TEMPEST Technical Authority – Glossary TEMPEST is the government codename for the program that contains compromising emanations, the unintended electromagnetic, acoustic, or vibrational signals that leak from equipment processing classified information. CTTA TEMPEST certification is not a credential a facility or a piece of hardware receives from the CTTA directly; it is the authority the CTTA exercises to certify that a facility, system, or installation meets the applicable national TEMPEST standards.

Only government employees can hold the role. Contractors may support TEMPEST work, but the certification authority itself does not travel outside the government.

What a CTTA Decides

The CTTA’s core function is applying the national TEMPEST framework to a specific facility or system. That starts with an assessment of the inspectable space, the three-dimensional area around classified processing equipment within which TEMPEST exploitation is not considered practical, or where the organization has authority to detect and remove eavesdropping threats.2National Institute of Standards and Technology. Inspectable Space – Glossary A larger controlled buffer around the facility means less shielding is needed; a wall shared with an uncontrolled space means more.

From that baseline, the CTTA determines:

  • Which equipment certification level applies to the hardware inside.
  • Which RED/BLACK isolation level applies to cabling and equipment layout.
  • What shielding, filtering, and grounding designs are required.
  • Whether proposed construction plans, particularly for Sensitive Compartmented Information Facilities, satisfy those requirements.
  • Whether any exception, such as allowing mobile devices into a classified space, is acceptable. That risk-assessment input goes to the Authorizing Official before the exception can be approved.

No system or facility processes classified material until the CTTA signs off. When a facility seeks an Authority to Operate, the CTTA conducts or validates the TEMPEST evaluation that feeds the decision.3Directorate of National Intelligence. Technical Specifications for Construction and Management of SCIFs

The Standards a CTTA Works From

Most TEMPEST documents are classified or distribution-restricted, but the framework is publicly identifiable. At the top sits CNSS Policy 300, the national policy on control of compromising emanations, which requires that systems and facilities handling national security information be reviewed for TEMPEST vulnerabilities.

Below that, CNSSI 7000, “TEMPEST Countermeasures for Facilities,” is the operational instruction. It requires a CTTA to conduct or validate every countermeasure review and to recommend the most cost-effective solution that keeps compromising emanations within the inspectable space.

Equipment-level requirements come from NSTISSAM TEMPEST/1-92, which defines the emission limits hardware must meet for TEMPEST certification. Installation practices, including RED/BLACK separation criteria for cabling and equipment placement, come from CNSSAM TEMPEST/01-13.

Certification Levels and Inspectable Space

Hardware used in classified environments must meet one of three TEMPEST certification levels under NSTISSAM TEMPEST/1-92:4National Institute of Standards and Technology. TEMPEST Certified Equipment or System – Glossary

  • Level I is the most stringent. It applies where an adversary could plausibly be within roughly one meter or in an adjacent room.
  • Level II provides moderate containment, designed against exploitation from about 20 meters of unobstructed distance or the equivalent through walls.
  • Level III is the least stringent, covering exploitation from roughly 100 meters of unobstructed distance.

NATO uses parallel designations under SDIP-27: Level A, B, and C correspond to NSA Levels I, II, and III. NATO generally does not test to Level C because most commercial IT equipment already meets those limits without modification.5NATO. TEMPEST Equipment Selection Process

RED/BLACK isolation follows the same logic. Level I is the tightest separation, applied to small inspectable spaces; Level III is the loosest, applied where large controlled zones supply natural standoff. The CTTA picks the level based on the physical layout and threat environment, then specifies minimum separation distances for cable runs, equipment placement, and grounding.6National Institute of Standards and Technology. RED/BLACK Concept – Glossary

In practice, that means classified network cables cannot share conduits with unclassified lines. RED and BLACK power circuits are separated, sometimes with dedicated transformer feeds. Equipment racks are physically segregated. Even the routing of fire alarm wiring matters if it passes through spaces where RED signals could couple onto it.

Shielding, Filtering, and Grounding

Three engineering techniques do most of the containment work, and the CTTA reviews all three.

Shielding usually takes the form of conductive enclosures, from individual equipment racks up to entire rooms, that block electromagnetic fields from escaping. The standard benchmark is 100 decibels of attenuation up to 10 GHz, measured under NSA 65-6 procedures.7Defense Logistics Agency. MIL-HDBK-1195 Radio Frequency Shielded Enclosures One hundred decibels means the signal outside the enclosure is ten billion times weaker than inside. Resonance inside the enclosure itself can create sharp dips in effectiveness at certain frequencies if the design does not account for them.

Filtering handles conducted emissions. Every conductor that penetrates a shielded boundary needs a filter: power lines including all phases and neutral, telephone cables, signal lines, fire alarm circuits, intrusion detection wiring, and any other control cabling. Filter performance is a known weak point; some tested filters provide 20 to 30 decibels less attenuation than required below several megahertz, which is why selection and verification matter.

Grounding and bonding create low-impedance paths for stray currents. Shielded enclosures use single-point grounding to the facility ground system, and the signal ground points inside a SCIF must be mapped and documented as part of the TEMPEST evaluation, because poor grounding can undermine even excellent shielding.

The CTTA in SCIF Accreditation

For SCIFs built under Intelligence Community Directive 705, TEMPEST countermeasures are designed in from the beginning rather than added later. The IC Technical Specifications require SCIF perimeter doors to meet TEMPEST requirements per CTTA guidance, and metallic penetrations through the perimeter may require dielectric breaks or grounding when the CTTA recommends it. SCIFs located outside the United States must have their TEMPEST countermeasures pre-engineered into the building.

The CTTA evaluation is a mandatory part of the accreditation package. No SCIF is accredited without it. Facilities with advanced TEMPEST protections and RF shielding can take up to 36 months to move from design to approval.

Inspections and Re-Evaluation

CTTA involvement continues after initial accreditation. A standard CTTA visual inspection follows a detailed checklist that in IC facilities requires documentation of:8Directorate of National Intelligence. SCIF TEMPEST Checklist

  • Floor plan diagrams showing the location, routing, and RED/BLACK identity of every signal line and distribution system in the SCIF.
  • Exit-point verification confirming where signal lines leave the SCIF and whether filters or isolation devices are installed on each one.
  • The location of all signal ground points.
  • Routing of all metallic conductors leaving the controlled area, including telephone, power, signal, alarm lines, pipes, and air ducts.
  • Separation distances between any radio transmission or reception device and the nearest RED equipment or cryptographic gear, with verification that radio power is isolated from RED processing power.

Re-evaluation is triggered whenever the security posture changes. Adding or replacing equipment, modifying the building perimeter, rerouting cables, or introducing wireless devices all require CTTA reassessment. Department of the Navy guidance requires system security posture reevaluation at least annually and whenever a significant modification changes the authorization status, with shorter cycles for systems carrying high or very high residual risk.

Consequences of Non-Compliance

For Department of Energy contractors and subcontractors, violations of classified information security requirements can bring civil penalties of up to $187,668 per violation. Ongoing violations count as a separate violation each day, so costs compound quickly.9eCFR. 10 CFR Part 824 – Procedural Rules for the Assessment of Civil Penalties for Classified Information Security Violations Insufficient funding is not accepted as a justification. In severe cases, the remedy is contract termination rather than a fine.

For individual employees and military personnel, failing to report a known TEMPEST vulnerability can trigger review under the personnel security adjudicative guidelines, specifically Guideline E on personal conduct and omissions. Clearance revocation ends a career in any position requiring access to classified information, and for military members can lead to involuntary separation or reclassification.

After a Suspected Compromise

If a TEMPEST compromise is suspected, reporting goes immediately to the Activity Security Manager or Facility Security Officer. If secure communications are unavailable, the initial report omits the location and classification details.10Center for Development of Security Excellence. Data Spills Student Guide The affected system is isolated to limit further exposure and preserve forensic evidence. The CTTA is then involved in the post-incident assessment: determining whether the emanation was actually exploitable given the facility’s inspectable space, identifying which countermeasure failed, and specifying corrective action before classified processing resumes.